|
Product Details:
Payment & Shipping Terms:
|
| Power: | 0.75KW | HP: | 1.2 |
|---|---|---|---|
| Color: | Black | Usage Environment:: | Fresh Water/Sea Water |
| Application:: | Water Supply | Shaft:: | SS 304/SS 316 |
| High Light: | above ground water pump,hot water circulation pump |
||
| Model | Voltage | HZ | Power(KW) | Power(HP) | Hmax(m) | Qmax(m³/h) | Port Size(inch/mm) |
| FEL-180 | 220V-380V | 50/60 | 0.18 | 0.25 | 5 | 8.4 | 50 1.5” |
| FEL-250 | 220V-380V | 50/60 | 0.25 | 0.35 | 8 | 9.6 | 50 1.5” |
| FEL-370 | 220V-380V | 50/60 | 0.37 | 0.50 | 11 | 12.6 | 50 1.5” |
| FEL-550 | 220V-380V | 50/60 | 0.55 | 0.75 | 10.5 | 14.4 | 50 1.5” |
| FEL-750 | 220V-380V | 50/60 | 0.75 | 1.00 | 11 | 16.5 | 50 1.5” |
| FEL-900 | 220V-380V | 50/60 | 0.90 | 1.2 | 22 | 18 | 50 1.5” |
Description
FEl swimming pool water pump is able to use in the salt water or chlorine filtered pools. Its built with a corrosion resistant marine grade cast iron motor housing and chemical resistant thermoplastic filter and engineer plastic pump body which allows the pump to be tough and durable. It provides high effective cleanin filtration basket which designed to capture and prevent fine debris from entering the pump,make the pump to supply a long time service.
Features:
* Suitable for pools up to 70,000 litres
* Max flow rate of 18000L/hr or 300L/ min
* Suitable for salt, chorine, in-ground and above-ground pools
* Corrosion-resistant marine grade cast iron motor housing
* Chemical-resistant thermoplastic filter cartridge tank body
* Durable construction
* Removable lint and hair trap/ filter
* Transparent twist on cover
* Built-in thermal protection
* Instruction manual
* One-year warranty
INSTALLATION
Only qualified licensed electrician should install pump and wiring.
IMPORTANT ELECTRICAL
Electrical Contractors Please Note: All 220/380 Volt 50Hz pumps must be wired to the main power
supply through an approved and correctly rated electrician.
PUMP MOUNT MUST
Be solid Level Rigid Vibration Free.
Allow use of short, direct suction pipe. (To reduce friction losses & don’t install the pump more
than 3M geometrical height from water level)
Allow for gate valves in suction and discharge piping.
Have adequate floor drainage to prevent flooding.
Be protected from excess moisture.
All adequate access for servicing pump and piping.
NOTICE
Pump suction and discharge connections have moulded in thread stops, DO NOT try to screw pipe
in beyond these stops.
The only routine maintenance is inspection/cleaning basket. Debris or trash that collects in basket,
well choke off water flow through the pump. Follow instructions below to clean basket:
Stop pump, close gate valve in suction and discharge, and release all pressure from
system before proceeding.
1. Unscrew cap lid(turn counterclockwise).
2. Remove strainer basket and clean. Be sure all holes in basket are clear, flush basket with water.
If basket is replaced backwards, cover will not fit on pre-filter body.
3. Clean and inspect lid Ring: re-install on cap cover.
WITH A FULL RANGE OF SIZES, they are IDEAL FOR SMALL, MEDIUM and LARGE spas – Our pumps start from the 0.5 HP for circulation pumps up to the 3HP for spa jets and a full range of sizes in between. Connection fittings for standard PVC 2inch (48.5mm) pipe.
HOW TO USE – It is best to always replace your pump with a pump of similar size and power rating. Changing over and fitting of the pump can be done by the handy person but it is recommended to get it done by a professional. Suitable as a direct replacement OR upgrade to existing pump.
Contact Person: Ms. Sindy Jin
Tel: +86-13535307437
Fax: 86-020-36401571
